Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm
Mounting Arm

Mounting Arm

M-100

$20.00
/
Shipping calculated at checkout.

The Mounting Arm allows you to mount One or Two devices Out front and Center on a Mountain or Road bike. It allows you to Slide and Rotate them to face forwards, backwards, right side up or upside down. Mount any combination of a camera, cycling computer, phone and light. Just one mount needed for all your electronic devices.

Works with all our adapters to mount Cycling Computers, Lights, Action Cameras and Sport watches

Features

  • Mount up to Two devices on one Mounting Arm
  • Mount your devices out-front or behind the bars
  • Rotate and slide your devices to multiple positions
  • Free up bar space with only one mount for all your devices
  • Buy only one mount and save money
  • No need to buy new mounts for new devices
  • Strong, light, and shock absorbing
  • Fits all 31.8mm diameter bars
  • Torque not to exceed 1.6Nm/14inlbs
Made from a CARBON composite Nylon
Weight 28g
Designed, engineered, and manufactured in the U.S.A

Instructions

Mounting Arm

  • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
  • Torque not to exceed 1.6Nm/14inlbs.

Adapters

  • Remove the bolt and washer from the adapter and install into the mounting arm slot.
  • Thread on the adapter with the washer on the opposite side flush against the bolt head.
  • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
  • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

  • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
  • Don’t use excessive force it may break the product and void the warranty.
  • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
  • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
  • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.

You may also like

Quick view
Garmin Computer Adapter
$10.00
Quick view
Wahoo Computer Adapter
$10.00
Quick view
Bryton Computer Adapter
$10.00
Quick view
Polar Computer Adapter
$10.00
Quick view
Camera & Light Adapter
$10.00
Quick view
Universal Adapter
$10.00
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter
Garmin Computer Adapter

Garmin Computer Adapter

AD-G100B

$10.00
/
Shipping calculated at checkout.

Mount your computer Out front and Center of the bars. Slide and Rotate to eliminate glare and optimize the viewing angle

Works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.

Features

  • Cycling Computer Adapter works with GARMIN® EDGE 200, 500, 800, 1000, Touring series computers.
  • Slide and Rotate: Slide and Rotate your computer to most positions.
  • Eliminate Glare: Rotate your computer to Eliminate Glare.
  • Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
  • Torque not to exceed 1.6Nm/14inlbs
Made from a CARBON composite Nylon
Weight 8g
Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

  • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
  • Torque not to exceed 1.6Nm/14inlbs.

Adapters

  • Remove the bolt and washer from the adapter and install into the mounting arm slot.
  • Thread on the adapter with the washer on the opposite side flush against the bolt head.
  • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
  • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

  • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
  • Don’t use excessive force it may break the product and void the warranty.
  • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
  • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
  • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter
Wahoo Computer Adapter

Wahoo Computer Adapter

AD-W100B

$10.00
/
Shipping calculated at checkout.

Mount your computer Out front and Center of the bars. Slide and Rotate to eliminate glare and optimize the viewing angle.

Works with WAHOO® Element Roam and Element Bolt series computers.

Features

  • Cycling Computer Adapter works with WAHOO® Element Roam and Element Bolt series computers.
  • Slide and Rotate: Slide and Rotate your computer to most positions.
  • Eliminate Glare: Rotate your computer to Eliminate Glare.
  • Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
  • Torque not to exceed 1.6Nm/14inlbs
Made from a CARBON composite Nylon
Weight 8g
Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

  • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
  • Torque not to exceed 1.6Nm/14inlbs.

Adapters

  • Remove the bolt and washer from the adapter and install into the mounting arm slot.
  • Thread on the adapter with the washer on the opposite side flush against the bolt head.
  • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
  • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

  • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
  • Don’t use excessive force it may break the product and void the warranty.
  • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
  • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
  • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter
Bryton Computer Adapter

Bryton Computer Adapter

AD-B100B

$10.00
/
Shipping calculated at checkout.

Mount your computer Out front and Center of the bars. Slide and Rotate to eliminate glare and optimize the viewing angle.

Works with BRYTON® Rider 10, 15, 320, 420, 530, 860 series computers.

Features

  • Cycling Computer Adapter works with BRYTON® Rider 10, 15, 320, 420, 530, 860 series computers.
  • Slide and Rotate: Slide and Rotate your computer to most positions.
  • Eliminate Glare: Rotate your computer to Eliminate Glare.
  • Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
  • Torque not to exceed 1.6Nm/14inlbs
Made from a CARBON composite Nylon
Weight 8g
Designed, Engineered and Made in the U.S.A

Instructions

Mounting Arm

  • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
  • Torque not to exceed 1.6Nm/14inlbs.

Adapters

  • Remove the bolt and washer from the adapter and install into the mounting arm slot.
  • Thread on the adapter with the washer on the opposite side flush against the bolt head.
  • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
  • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

Carbon Fiber Stem Mount

  • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
  • Don’t use excessive force it may break the product and void the warranty.
  • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
  • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
  • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter
Polar Computer Adapter

Polar Computer Adapter

AD-P100B

$10.00
/
Shipping calculated at checkout.

Mount your computer Out front and Center of the bars. Slide and Rotate to eliminate glare and optimize the viewing angle.

    Works with Polar® M460 and V650 cycling computers.

      Features

      • Cycling Computer Adapter works with Polar®  M460 and V650 cycling computers.
      • Slide and Rotate: Slide and Rotate your computer to most positions.
      • Eliminate Glare: Rotate your computer to Eliminate Glare.
      • Optimize the Viewing Angle: Rotate and Slide the computer to your Optimum-Viewing Angle.
      • Torque not to exceed 1.6Nm/14inlbs
      Made from a CARBON composite Nylon
      Weight 8g
      Designed, Engineered and Made in the U.S.A

      Instructions

      Mounting Arm

      • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
      • Torque not to exceed 1.6Nm/14inlbs.

      Adapters

      • Remove the bolt and washer from the adapter and install into the mounting arm slot.
      • Thread on the adapter with the washer on the opposite side flush against the bolt head.
      • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
      • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

      Carbon Fiber Stem Mount

      • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
      • Don’t use excessive force it may break the product and void the warranty.
      • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
      • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
      • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter
      Camera & Light Adapter

      Camera & Light Adapter

      AD-CL100B

      $10.00
      /
      Shipping calculated at checkout.

      Mount your Action Camera or Cycling Light Out front and Center using our Camera/Light adapter. Its a three tab design that is compatible with any action camera or light that has a two tab adapter and uses a M5 bolt. Mount your camera or light right side up, upside down, slide it forwards and backwards or rotate it to capture all your experiences on video or light up the night.

        Works with all GoPro® Hero Cameras, Action Cameras and Lights

          Features

          • Camera and Light Adapter works with all GoPro® Hero and other style Action cameras and Cycling Lights.
          • Positions your Camera or Light Out front and Center
          • Camera can be mounted facing forward or backwards
          • Rotate and Slide your Camera to capture different views
          • Mounts Upside down or Right side up
          • Torque not to exceed 1.6Nm/14inlbs.

          Made from a CARBON composite Nylon
          Weight 15g
          Designed, Engineered and Made in the U.S.A

          Recommendations

          • We recommend mounting the Camera adapter in the middle to the back of the mount for better stability.

          Instructions

          Mounting Arm

          • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
          • Torque not to exceed 1.6Nm/14inlbs.

          Adapters

          • Remove the bolt and washer from the adapter and install into the mounting arm slot.
          • Thread on the adapter with the washer on the opposite side flush against the bolt head.
          • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
          • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

          Carbon Fiber Stem Mount

          • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
          • Don’t use excessive force it may break the product and void the warranty.
          • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
          • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
          • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter
          Universal Adapter

          Universal Adapter

          AD-U100B

          $10.00
          /
          Shipping calculated at checkout.

          Mount any 31.8mm bar mountable device on the Universal Adapter. Mount Cycling Computers, Lights and Sport Watches, such as NITERIDER®, CYGOLITE®, EXPOSURE®, CATEYE®, APPLE® and POLAR®.

          Features

          • Mount any 31.8mm bar mountable device on the Universal Adapter
          • Mount a Light Out front, Center and lower to the ground for improved lighting
          • Mount your Cycling Computer or Sport Watch Out front
          • Torque not to exceed 1.6Nm/14inlbs
          Made from a CARBON composite Nylon
          Weight 12g
          Designed, Engineered and Made in the U.S.A

          Instructions

          Mounting Arm

          • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
          • Torque not to exceed 1.6Nm/14inlbs.

          Adapters

          • Remove the bolt and washer from the adapter and install into the mounting arm slot.
          • Thread on the adapter with the washer on the opposite side flush against the bolt head.
          • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
          • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

          Carbon Fiber Stem Mount

          • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
          • Don’t use excessive force it may break the product and void the warranty.
          • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
          • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
          • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter
          Camera Adapter

          Camera Adapter

          AD-GP100B

          $10.00
          /
          Shipping calculated at checkout.

          Get your Camera off the bars and Out front and Center. Mount it right side up, upside down, slide it forwards and backwards or rotate it to capture all your experiences on video. Easily remove and attach the camera with the quick release adapter.

            Works with all GoPro® Hero Cameras and Action Cameras
              (Note: Cameras require the use of a GoPro® buckle to mount to our adapter.)

                Features

                • Camera Adapter works with all GoPro® Hero Cameras and Action Cameras
                • Positions your Camera Out front and Center
                • Camera can be mounted facing forward or backwards
                • Rotate and Slide your Camera to capture different views
                • Mounts Upside down or Right side up
                • Easily remove and attach the camera with the quick release adapter
                • Torque not to exceed 1.6Nm/14inlbs.

                Made from a CARBON composite Nylon
                Weight 15g
                Designed, Engineered and Made in the U.S.A

                Recommendations

                • We recommend mounting the Camera adapter in the middle to the back of the mount for better stability.

                Instructions

                Mounting Arm

                • Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
                • Torque not to exceed 1.6Nm/14inlbs.

                Adapters

                • Remove the bolt and washer from the adapter and install into the mounting arm slot.
                • Thread on the adapter with the washer on the opposite side flush against the bolt head.
                • Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
                • Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.

                Carbon Fiber Stem Mount

                • Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
                • Don’t use excessive force it may break the product and void the warranty.
                • Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
                • Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
                • Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
                Back to Mounting Arms