Use with any adapter and a M4 Flat head socket bolt
Comes in 6 colors
Blue, Orange, Black, Red, Green and Purple
Weight 0.5 grams
Instructions
Mounting Arm
Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.
Adapters
Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.
Carbon Fiber Stem Mount
Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
M4 x 20mm long Socket Head Cap Screw Stainless to be used with our mounting arm.
M4 x 20mm SHCS
Stainless Steel
M3 Hex tool
Instructions
Mounting Arm
Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.
Adapters
Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.
Carbon Fiber Stem Mount
Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
M4 x 10mm long Flat Head Cap Screw Stainless to be used to attach any adapter to the mounting arm.
M4 x 10mm FHCS
Stainless Steel
Instructions
Mounting Arm
Mount onto the handle bar to the left or right of the stem and tighten with a 3mm Hex wrench.
Torque not to exceed 1.6Nm/14inlbs.
Adapters
Remove the bolt and washer from the adapter and install into the mounting arm slot.
Thread on the adapter with the washer on the opposite side flush against the bolt head.
Torque to no more than 1.6Nm/14inlbs using a Hex wrench.
Apply a small amount of Blue LOCTITE® #242 to the threads of the adapter bolt if needed to keep it from coming loose.
Carbon Fiber Stem Mount
Replace the stem’s screws (the bottom left and right), by inserting the spacer first, then the mount, washer and finally the long black Titanium screws.
Don’t use excessive force it may break the product and void the warranty.
Tighten the screws using the torque suggested by your stem manufacturer approx. 2 to 3Nm and lube the bolt with anti-seize grease.
Check holes for alignment between front clamp & stem. If there is an alignment mismatch top to bottom, the screw can undergo abnormal stresses and could break.
Before tightening make sure that the titanium screw penetrates the stem with full thread engagement. If screws don’t fully engage, please contact us.
